Á¦Ê¿ÀÖËÅ·þÇý¶¯Æ÷άÐÞͼ½â£ºÉϺ£Ñö¹âµç×ӿƼ¼ÓÐÏÞ¹«Ë¾×¨Òµ´Óʸ÷Æ·ÅÆËÅ·þÇý¶¯Æ÷άÐÞ,ËÅ·þµç»úάÐÞ,´¥ÃþÆÁάÐÞ,±äƵÆ÷άÐÞ,ËÅ·þÆ÷άÐÞ,ËÅ·þ¿ØÖÆÆ÷άÐÞ,Êý¿ØϵͳάÐÞ¸ÄÔ죬»úÆ÷ÈËάÐÞ±£ÑøÒÔ¼°¸÷Öְ忨,оƬ¼¶Î¬ÐÞά»¤,Ãâ·Ñ¼ì²â,¿ìËÙάÐÞ,²¿·ÖÁ¢µÈ¿ÉÈ¡!
²©ÊÀÁ¦Ê¿ÀÖËÅ·þÇý¶¯Æ÷άÐÞ¼ì²â£º
F644 Negative Travel Limit Switch Detected
¼ì²âµ½¸ºÐгÌÏÞλ¿ª¹Ø
The negative travel limit switch has been actuated. The axis has been
stopped with the error reaction "set velocity command value to zero". Bit 2
of P-0-0090, Travel limit parameter has been set to "Exceeding the
travel limit is considered as an error", or a drive control command has
been started while the axis limit value is exceeded (e.g. drive-controlled
homing).
¸ºÐгÌÏÞλ¿ª¹ØÒÑÆô¶¯¡£ÖáÒѾÒÔ´íÎó·´Ó¦¡°½«ËÙ¶ÈÃüÁîÖµÉèÖÃΪÁ㡱ֹͣ¡£µÚ2λP-00090ÖУ¬ÐгÌÏÞÖƲÎÊýÒÑÉèÖÃΪ¡°³¬¹ýÐгÌÏÞÖƱ»ÊÓΪ´íÎó¡±£¬»òÇý¶¯¿ØÖÆÃüÁîÒÑÔÚ³¬¹ýÖἫÏÞֵʱÆô¶¯£¨ÀýÈ磬Çý¶¯¿ØÖƹé룩¡£
Cause:ÔÒò£º
The negative travel limit switch has been actuated
¸ºÐгÌÏÞλ¿ª¹ØÒÑÆô¶¯
Remedial action:²¹¾È´ëÊ©£º
1. Reset the error
ÖØÖôíÎó
2. Activate the power supply
¼¤»îµçÔ´
3. Move the axis into the permissible working range
½«ÖáÒƶ¯µ½ÔÊÐíµÄ¹¤×÷·¶Î§ÄÚ
Note: The drive will not accept any command values that lead further away from the permissible range. Specifying such a command will again result in this error.×¢Ò⣺Çý¶¯Æ÷²»»á½ÓÊÜÈκÎÔ¶ÀëÔÊÐí·¶Î§µÄÃüÁîÖµ¡£Ö¸¶¨ÕâÑùµÄÃüÁÔٴε¼Ö´˴íÎó¡£
תÔØÇë×¢Ã÷³ö´¦£ºÉϺ£Ñö¹âµç×ӿƼ¼×¨ÒµËÅ·þÇý¶¯Æ÷άÐÞ,ËÅ·þµç»úάÐÞ
±¾ÎÄÁ´½Ó£ºhttp://m.tlwyjt.net/fuwu/Services_Show24625.htm
ËÅ·þÇý¶¯Æ÷άÐÞ ËÅ·þµç»úάÐÞ ´¥ÃþÆÁάÐÞ ±äƵÆ÷άÐÞ
µç»°£º021-50157782
ÊÖ»ú£º13817011982 ΢ÐÅͬºÅ
ÓÊÏ䣺shygdzi@163.com
ÁªÏµÈË£ºÕŹ¤
꿅᣼http://m.tlwyjt.net
¡¾ ÎÒÃÇÈ·±£Ð޺òâÊԺøø¿Í»§£¡£¡£¡£¡¡¿
ÏÂһƪ£ºº£µÂººHi800-DÊý¿ØϵͳTNCζȹý¸ßάÐÞά»¤